How to Measure for a Roof Lantern or Flat Rooflight
Correct measurements are essential when ordering roof glazing. The most common mistake is assuming that every roof lantern and flat rooflight uses the same reference dimension. Lumina Design supplies several product families, and the measuring rule changes between them.
For Atlas roof lanterns and Atlas fixed or electric opening flat rooflights, order using the external finished kerb dimensions. For Infinity framed and frameless fixed rooflights, order using the internal structural opening. Infinity walk-on rooflights use overall external dimensions and should be confirmed from the project drawing.
Before measuring, identify the exact product range. A correct dimension taken from the wrong reference point can still result in the wrong unit.
Quick measuring guide by product
Product | Ordering dimension | Key point |
Atlas contemporary or traditional roof lantern | External finished kerb | Measure the outside of the completed upstand. Atlas lantern ringbeam footprint is 67mm per side. |
Atlas stock or made-to-measure fixed flat rooflight | External finished kerb | Measure the outside of the completed upstand. The pitched side is measured along the slope. |
Atlas electric opening flat rooflight | External finished kerb | Uses the same external-kerb rule as the fixed Atlas rooflight. The pitched side is measured along the slope. |
Infinity framed fixed rooflight | Internal structural opening | Measure the clear opening inside the upstand. Standard pricing assumes an 80mm finished upstand width. |
Infinity frameless fixed rooflight | Internal structural opening | Measure the clear opening. The installer must form the stepped support shown in the fitting guide. |
Infinity thermal walk-on rooflight | Overall external dimension | Confirm frame or glass reference and clear opening from the project drawing before ordering. |
How to measure an Atlas roof lantern
Atlas contemporary, traditional, stock and special-offer lanterns are specified by the external finished kerb size. The dimensions you give Lumina should match the outside length and outside width of the finished upstand where the lantern will sit.

Identify the outside edges of the finished kerb or upstand.
Measure the external length at the point where the lantern will be seated.
Measure the external width in the same way.
Measure both diagonals. Matching diagonals confirm that the kerb is square.
Check the size against the product drawing before the kerb is finalised.
The Atlas lantern ringbeam footprint is 67mm on each side. For planning purposes, the clear internal opening is therefore approximately 134mm smaller than the external kerb dimension in each direction.
Worked Atlas lantern example
A lantern ordered at 2500 × 1300mm external kerb gives an approximate clear internal opening of 2366 × 1166mm: 2500 − 134 = 2366mm, and 1300 − 134 = 1166mm. Use this calculation for planning the opening; order the lantern as 2500 × 1300mm external kerb.
Do not order an Atlas lantern from the plastered ceiling opening. The external finished kerb is the controlling order size.
How to measure an Atlas flat rooflight
Atlas stock, made-to-measure and electric opening flat rooflights all use the external finished kerb dimensions. The same rule applies whether the rooflight is fixed or opens electrically.
Measure the outside width of the completed upstand.
Measure the outside length of the completed upstand.
Where the upstand is pitched, measure the pitched side along the slope rather than using a horizontal plan dimension.
Check both diagonals to confirm the upstand is square.
Compare the result with the product’s measuring image and fitting information before ordering.
If the rooflight is listed as 1000 × 1500mm external kerb, the completed outside kerb must match that ordering size. Do not deduct the frame width, and do not substitute the internal ceiling opening.
For an electric opening rooflight, the measurement convention does not change. You should still provide the external finished kerb dimensions, including the sloping measurement where applicable.
How to measure Infinity framed and frameless rooflights
Infinity framed and frameless fixed rooflights use the internal structural opening. This is the clear opening between the inside faces of the upstand, rather than the external kerb size.

For the Infinity framed product, standard pricing assumes an 80mm finished upstand width. The manufacturer’s current product information specifies a minimum 5-degree upstand pitch and a 150mm upstand height. If your finished upstand is wider, contact Lumina before ordering because the overall frame size and support details need checking.

The Infinity frameless product requires a stepped support and weathering detail because it has no aluminium perimeter frame. The manufacturer recommends an upstand pitch of 2–4 degrees. Your installer should use the current Infinity fitting guide when constructing the support.
What about Infinity walk-on rooflights?
Infinity thermal walk-on rooflights use overall external dimensions, rather than the internal-opening rule used for the framed and frameless fixed Infinity products. Their support, loading and clear opening must be confirmed from the project-specific drawing. Send Lumina the intended use, required size and support details before ordering.
Checks to make before placing the order
Confirm the product family: Atlas, Infinity framed, Infinity frameless or walk-on.
Write down whether the quoted dimension is external kerb, internal opening or overall external size.
Measure length, width and both diagonals with the finished upstand accessible.
Check the required pitch, upstand height, finished upstand width and support detail.
Allow for roof coverings and weatherproofing when establishing the finished kerb.
Ask the installer to check the current product drawing before manufacture begins.
Send photographs or a marked-up sketch if any dimension or reference point is unclear.
Frequently asked questions
Are Atlas electric opening rooflights measured internally?
No. Atlas electric opening flat rooflights are ordered using the external finished kerb dimensions, just like Atlas fixed flat rooflights.
Can I calculate an Atlas lantern size from the ceiling opening?
You can estimate for planning, but the lantern must be ordered from the external finished kerb. The Atlas ringbeam footprint is 67mm per side, so the approximate clear opening is the external kerb size minus 134mm in each direction.
Why do Infinity fixed rooflights use a different measurement?
Their product construction and support details differ from the Atlas range. The Infinity framed and frameless fixed products are priced and ordered from the internal structural opening, so the product name must be confirmed before dimensions are supplied.
What if the kerb is not square?
Do not rely on a single length and width. Measure both diagonals and ask the builder to correct the upstand before ordering or installation. A roof glazing unit cannot compensate for a badly out-of-square kerb.
Should I measure before or after the roof covering is fitted?
The measurement must represent the finished reference dimension used by the selected product. Your builder should account for the completed upstand and weathering build-up. If the kerb is still being built, send Lumina the drawing and proposed construction before the final size is agreed.
Can Lumina check my measurements?
Yes. Lumina Design is a supply-only specialist, but we can help identify the correct measuring convention and review the information you send. The installer remains responsible for the structure, kerb construction, falls, support and weatherproofing.
Send us your dimensions before ordering
Email sales@luminadesign.co.uk with the product name, length, width, two diagonal measurements, delivery postcode and photographs or drawings of the kerb. Alternatively, call 01656 630037. We will help you establish which dimension the product requires and prepare a quotation for the correct specification.

Comments